All the Controls products ASTM C standard. Enter now!. Request PDF on ResearchGate | Loading rate concerns in ASTM C | ASTM C remains one of the most prescribed tests for. This document describes the main differences between ASTM C and ASTM C when it comes to testing of flextural strength in fiber reinforced concrete.
|Published (Last):||20 July 2016|
|PDF File Size:||3.88 Mb|
|ePub File Size:||17.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Available from a 1 mm 0. Measurement of beam deflection and toughness This test is performed to assess the flexural performance and the residual resistance characteristics of fiber reinforced concrete FRC and shortcrete. Universal materials testing software for static hydraulic, electromechanical and torsion testing systems – WBB. They may also be used to monitor concrete quality, to verify compliance with construction specifications, obtain flexural strength data on fiber-reinforced concrete members subject to pure bending, or to evaluate the quality of concrete in service.
ASTM C1609 Fiber-Reinforced Concrete Flexural Test Equipment
By means of our bend testing expertise and modular product design, we will help find the testing solution that is right for you. Universal, open structure flexural frame, kN cap. It provides for determination of specimen toughness based on the area under the load-deflection curve up to a prescribed deflection see Note 2 and the corresponding equivalent flexural strength ratio.
Please confirm that you agree with our privacy and cookies policy to submit this form. E Deflectometer Deflection Gauge. WaveMatrix 2 for Dynamic Testing. In some cases, fibers may increase the residual load and toughness capacity at specified deflections while producing a first-peak strength equal to or only slightly greater c169 the flexural strength of the concrete without fibers. How can we help you?
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Home Products Search results Results for: A specimen size different from the two preferred specimen sizes is permissible.
Residual strength is not a true stress but an engineering stress computed using simple engineering bending theory for linear elastic materials and gross uncracked section properties.
Flex Testing of Fiber Reinforced Concrete to ASTM C1609-10
A specially configured universal test machine capable of servo-controlled operation is used with the net deflection of the center of the beam measured and used to control the rate of f1609 of deflection. This test method may be used for comparison of mixtures, quality control, and research and development. Email addresses can only contain letters, numbers and the following special characters: The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
The first-peak strength, peak strength, and residual strengths determined by this test method reflect the behavior of fiber-reinforced f1609 under static flexural loading.
Fiber-reinforced concrete is influenced in different ways by the amount and type of fibers in the concrete. Link to Active This link will always route to the current Active version of the standard. Repair Services and Parts.
Link to Active This link will always route to the current Active version of the standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
Software for Series Systems. Bluehill LE for Basic Testing.
Note 5 — The results obtained using one size molded specimen may not correspond to the performance of larger or smaller molded specimens, concrete in large structural units, or specimens sawn from such units. The loading and specimen support system is capable of applying third-point loading to the specimen without eccentricity or torque.
Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models. At the option of the specifier of tests, it provides for determination of specimen toughness based on the area under the load-deflection curve up to a prescribed deflection see Note 1.
ASTM C Fiber-Reinforced Concrete Flexural Test Equipment
We offer machines, apparatus, c1069, tensile grips, test fixtures, clamps, holders, jigs, asttm, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.
Note 2 — Specimen toughness expressed in terms of the area under the load-deflection curve is an indication of the energy absorption capability of the particular test specimen, and its magnitude depends directly on the geometry of the test specimen and the loading configuration.
Work Item s – proposed revisions of this standard. Note 1 Residual strength is not a true stress but an engineering stress computed using simple engineering bending theory for linear c160 materials and gross uncracked section properties.